If it does not, click the Start button and choose Run. The Setup Wizard should run automatically, and the. Non-interfering channels are 1, 6 and 11. Cara setting akses point sebagai wireless repeater pada WAP54G Setelah jendela konfigurasi terbuka, Klik AP Mode kemudian pilih Wireless Repeater. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators. Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Channel and SSID must be typed the same on both WAP54G’s in order for them to communicate. The default channel is 6, and the SSID is Linksys. #CARA SETTING WIFI LINKSYS WAP54G SETUP PASSWORD#Username is left blank, and password is admin. By default, the WAP54G comes with a default IP address of 192.168.1.245. For example 192.168.1.246, and 192.168.1.247.Īfter you have changed the IP address of the WAP54G, login to the access point via any web browser. Begin by placing the AP’s in the same room, and connect the FIRST Linksys wireless access point to your switch or PC. Note: Both Linksys WAP54G’s must be configured with different IP addresses in order to communicate. The CD will allow you to follow their instructions on setting up your new access point. If you are not familiar with changing the IP address on your computer, please use the included CD to configure the AP. Configure your managing computer to use a static IP address to the same subnet as the 192.168.1.xx to initially configure the unit. #CARA SETTING WIFI LINKSYS WAP54G SETUP HOW TO#Government & Military Wireless Bridge KitsĪ linksys wireless access point, or linksys wireless router can be used as a bridge between two or more locations. Although it is not recommended to use the linksys wireless router as a wireless bridge, it is possible. In the following explanation, we use a pair of Linksys WAP54G to create a wireless bridge, and show you how to setup a linksys wireless bridge mode.īegin by placing the AP’s in the same room, and connect the FIRST Linksys wireless access point to your switch or PC.īy default, the WAP54G comes with a default IP address of 192.168.1.245.Licensed Wireless Point to Point Systems.The repeater doesn't seem to recognize the WRT. So, I tried some different scenarios based on your suggestions with the same results. I tried both ways but didn't get any different results. Cannot ping the WRT when associated with the WAP and vice versa.Ĥ) The only difference I see in your setup is that you had the WAP set on channel one. #CARA SETTING WIFI LINKSYS WAP54G SETUP PC#Wireless PC (will attach to either the WRT or WAP depending on location in my home)ĭHCP Turned On (Range 192.168.1.100-192.168.1.25 4)Ģ) The Wireless MAC address from the WRT is entered on the WAP AP configuration screenģ) Changed the SSID to MySSID (WRT) and MySSID1 (WAP). Wireless PC (can connect to both the WRT (192.168.1.1) and WAP (192.168.1.245)ĬABLE modem-WRT54G - WAP54G (located in another room) If my interpretation is wrong, please advise.ĭuring intial setup of the WRT and the WAPĬABLE modem-WRT54G-W AP54G The 30-30-30 reset If the above instructions don't work you can always try the 30-30-30 reset as follows: When router is powered on, press the reset button and hold for 30 seconds. Linksys Model WAP54G WIFI Wireless G Access Point WAP with SES See more like this. Untuk Linksys WAP54G Sambungkan AP dengan komputer anda menggunakan kabel stright Ubah ip komputer anda menjadi 192.168.1.xxx ( xxx boleh bebas asal jangan 245 dan dibawah 255 ) coba ping ke ip 192.168.1. I understand this to be possible from the Linksys document. Linksys WRT54G V2.2 DD-WRT Tomato wireless Internet Access Point Repeater Bridge. The 30-30-30 reset If the above instructions dont work you can always try the 30-30-30 reset as follows: When router is powered on, press the reset button and hold for 30 seconds. Linksys Model WAP54G WIFI Wireless G Access Point WAP with SES See more like this. I'm attempting to use the WAP as a wireless range extender for my home network. Linksys WRT54G V2.2 DD-WRT Tomato wireless Internet Access Point Repeater Bridge. If you're able to get it working as I expect it to, I'll bump it up to 500 points. If you are able to determine where I'm going wrong I'll give 250 points. Step 2: Open a web browser like Internet Explorer. I know my way around but am not a networking genious. Step 1: Connect the WAP54G directly into one of the WRT54G’s numbered ports. This is the procedure I followed from Linksys: **&p_li=&p_topview=1 Based on Linksys documentation it seems I've followed the procedure. Ping the WAP54G (192.168.1.245) and cannot ping the WRT54G (192.168.1.1)Īt this point I'm not able to browse to the internet. I determine this because of a much stronger signal (100%) verses what I would normally get. After a bit of time, my laptop seems to roll over to the WAP54G.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |